This automatic optical fiber tensile testing system is made for operator skill impartial use within production and laboratory configurations. Two basic model designs enable the consumer to pick between a set up for standard linear proof testing and with additional mandrels for rotary high power testing.
The linear edition is designed for production evidence testing with causes as much as 22 N. Motorized clamps with carefully developed rubber inserts ensure that the Optical Fiber Ribbon Machine is not really damaged within the testing procedure whilst concurrently eliminating the requirement for an outside air supply. Degrees of tugging force, pulling velocity and hold time are programmable and conveniently accessible to the owner through the built-in LCD touchscreen display manage. Information from tests can be stored and accessed using the Universal serial bus port or Ethernet user interface.
Mandrels of the same style as in NYFORS’ optical fiber recoaters can be mounted on the evidence tester in the rotary high power configuration. The fiber is covered round the two mandrels which support it having a unique clamping system. In this way higher lots can be employed on the fiber, allowing breaking power tests under managed conditions.
Adjustable clamp placement facilitates screening with the highest force amounts as well as screening of short fiber lengths. The compact and light bodyweight design makes the instrument simple to maneuver in a lab environment and also to incorporate in a production work bench where space are at a premium. The equipment is really a compact and lightweight instrument ideal for testing the potency of optical materials up to 30 N. The machine is developed to meet all kinds of programs where a strength check needs to be carried out.
The device is designed with the user in mind. The Secondary Coating Line is definitely positioned in the guided linear clamps, and also the testing starts instantly with a “One Touch” go switch. The built in microprocessor controls all of the essential parameters like tugging force, pulling speed and hold time. This permits for any totally managed check every time.
The device can be connected to another PC, which enables usage of all programmable guidelines and configurations. The machine is adapted to stand-alone use or to the integration into various subsystems. The equipment has an substantial ability of logging and conserving information including pulling force, pulling speed and fiber diameter along with other guidelines.
Two recoat injector designs can be found. The PTR307 utilizes an automated water pump to inject the recoat materials. The amount of materials dispensed from the automated injector is controlled by hand using the top-installed “Inject” button or programmed to the machine utilizing the tablet pc controller. The PTR307B comes with a manual recoat shot program that will require an individual to manually dispense the recoat materials to the mold cavity; a replacement injector for the PTR307B recoater is available listed below. Make sure you note the automatic injector is simply suitable for high-index recoat material, while the handbook injector is compatible with each reduced- and- index recoat material; they are both marketed individually listed below. Make sure you contact Technology Support to learn more.
he manual injector can be installed to suitable Optical Fiber Coloring Machine using the 4-40 screws on the recoater housing (see picture towards the right). Make use of a 3/32″ hex key to safe the injector prior to use. For connecting the PTRRRM for the recoater mold, tighten up the connector after the eco-friendly plastic tubing, then loosen by way of a 1/4 consider allow for rotation.
The injector comes with a distribution device and two-position selection lever for directing the stream of recoat materials. A knurled dispensing attach having an internal plunger acts as a syringe for that recoat materials. To fill the syringe, point the lever downward (i.e., towards the recoat container), then spin the knurled dispensing screw counterclockwise until it spins easily to fill the syringe (demonstrated inside the photo to the right). Then, to inject the recoat material to the mold, point the lever horizontally (i.e., dealing with the knurled attach) and spin the screw clockwise till near the finish from the journey range is reached. Steer clear of bottoming out iuwekk dispenser because this may damage the interior plunger; also take care when re-engaging the threads to prevent go across threading the dispensing attach. A number of fill/inject steps may be needed until air is displaced within the system. Use camera lens tissue as well as an acetone or alcohol cleansing solution to gather any excess recoat material that runs from the mold.